REGBOT version 3

Revision as of 17:40, 30 October 2016

Aim

• maintain frame,
• Avoid too many satellite PCB's,
• more powerfull 5V,
• fix PCB errors on version 2,
• new servo interface plug
• battery saver - turn OFF if battery voltage is low.
• battery saver - turn IR sensor off if not used.

Status and observations

• Line sensor low power pin (Teensy pin 25) now working. Pin 25 set to output in main.cpp (line 125), and pulsed in main.cpp (line 425 and 466). Line estimate seems OK (after calibration) - line sensor calibration missing in regbot.ini.
• IR sensor power control is OK. IR sensor calibration missing in regbot.ini.
• Power off by "halt" and by too low battery voltage is OK, back on by "power" button in both cases OK. Power off (by halt), no USB, then power on by power button is OK.
• wifi (on board part) is working (client is not) - tested with putty (not on SSID=device)
• Servo plog (teensy pin 25 (PWM) is also line sensor pin, teensy pin 5 (PWM) is also SPI interface, teensy pin A14 (analog out), teensy pin 18 (also linesensor power pin).
• IMU interface OK
• start button OK
• servo 1-k implemented (400hz, 10 bit PWM control) - and tested - +/- 512 gives about 90 deg, not 180 as expected (bad Hobby King servo for purpose). But modifies motor-PWM, this works only on new (version 3.5) motherboard.
• current sensor OK
• motor control OK
• start button OK
• version 3 ready for production - with socket for cheaper motor controller.

Missing/bugs

Software robot side (Teensy)

• control implement test of edge, wall and forward distance controllers - partially tested (velocity, heading, position and balance seems OK)

• wifi - is OK after a reboot,but stops after a few minutes, if no wifi client is attached.

• AD converter for "servo" 4 and 5 (when not output pins) is not implemented, and should be available as continue condition in missions.

Software client side

Servo debug page is a mess with edit/apply/cancel, as most actions work instantaneously.

Tab order is a mess.

Help in control dialogue is missing - should refer to wiki page.

Teensy pin assingnment

GND side

• 0 serial RX (wifi)
• 1 serial TX (wifi)
• 2 motor left direction
• 3 motor left PWM
• 4 motor left D2 enable -> flyttes til right motor PWM
• 5 servo pin 3 (PWM) - og 2nd SPI CS pin (4) (see also teensy pin 24)
• 6 Start button
• 7 motor slew ctrl -> flyttes til motor enable D2
• 8 motor right direction
• 9 motor right PWM -> flyttes til servo PWM (servo pin 4)
• 10 motor right D2 enable - > flyttes til servo PWM (servo pin 6)
• 11 SPI MOSI
• 12 SPI MOSI

Vin side

• 13 heart beat LED og SPI clock
• 14 (A0) IR dist 2
• 15 (A1) IR dist 1
• 16 I2C SCL
• 17 I2C SDA
• 18 Line sensor LED power (skal ikke også til servo pin)
• 19 encoder left B
• 20 encoder left A
• 21 encoder right B
• 22 encoder right A
• 23 (A9)battery voltage

End

• A14 (analog out) servo pin 5 (i/o, ikke PWM) - for switch in or signal out (mostly)

2nd row

• A10 motor current left
• A11 motor current right

button side

• A12 line sensor pin 3
• A13 line sensor pin 4
• A15 line sensor pin 5
• A16 line sensor pin 6
• A17 line sensor pin 7
• A18 line sensor pin 8
• A19 line sensor pin 9
• A20 line sensor pin 10

• 24 SPI CE (SPI CS pin (pin 3))
• 25 Line sensor LED HIGH
• 32 IR power on
• 33 Robot power on

Message to-from regbot

PID control message

All controlls is formatted with 26 values, and looks like this example (balance)

cbal 1 -3 0 1 9999.99 1 0 1 1 1 0.029 0.001 0 1 1 1 0.1 5 1 0 1 0 1 1 1 99.99

The indivitual numbers are - after the controller keyword (here 'cbal'):

 1 cbal 1 // use (any part of controller)
 2     -3 // Kp
 3      0 1 9999.99 1 // integrator (use, tau, limit, (and_zero - not implemented))
 7      0 1 1 // lead forward (use, zero, pole)
 10     1 0.029 0.001 // lead backward (use, zero, pole)
 13     0 1 1 // pre-filt (use, zero, pole)
 16     1 0.1 5 1 // post integrator (use, tau, limit, and_zero)
 20     0 1 // feed forward (use, Kff)
 22     0 1 1 // feed forward pole-zero (use zero pole)
 25     1 99.99 // output limit (use, limit)