Terrain hopper steering
(→Maxon motor) |
|||
| Line 1: | Line 1: | ||
Back to [[TerrainHopper]] | Back to [[TerrainHopper]] | ||
| + | |||
| + | == Steering == | ||
| + | |||
| + | Distance between axles is 0.93 m | ||
| + | |||
| + | Distance between king pins 0.55 m | ||
| + | |||
| + | Max steering angle actual is about 32 degrees (center heading) | ||
| + | |||
| + | Steering is limited to +/- 28 degrees in RHD, this gives a turning radius of 2m. | ||
| + | |||
==CAD drawings== | ==CAD drawings== | ||
| Line 6: | Line 17: | ||
See https://cad.onshape.com/documents/97c36fb21a7a858c57c0af9f/w/0d867586bc28d7a9194d7ff3/e/ca0f539fa3eee3cfe0ed4130 | See https://cad.onshape.com/documents/97c36fb21a7a858c57c0af9f/w/0d867586bc28d7a9194d7ff3/e/ca0f539fa3eee3cfe0ed4130 | ||
| − | ==Overview of new steering | + | ==Overview of new steering== |
[[File:off-the-shelf-parts.png | 600px]] | [[File:off-the-shelf-parts.png | 600px]] | ||
Revision as of 13:57, 3 July 2019
Back to TerrainHopper
Contents |
Steering
Distance between axles is 0.93 m
Distance between king pins 0.55 m
Max steering angle actual is about 32 degrees (center heading)
Steering is limited to +/- 28 degrees in RHD, this gives a turning radius of 2m.
CAD drawings
Overview of new steering
Figure 1. New steering part maintaining original steering axle position, but replacing with bearings and a belt drive to a maxon gear motor. This figure points to most of the off-the-shelf parts used.
See purchase detail in Terrain-hopper binder (Christian office - red binder).
Figure 2. New steering part maintaining original steering axle position, but replacing with bearings and a belt drive to a maxon gear motor. This figure points to most of the parts that needs workshop assistance. Most of the parts - except axlesl (7 and 8) - can be manufactored on own workshop. The axles will be manufactored by axle supplier.
Maxon motor
The motor for steering is a Gear-motor-encoder combination from Maxon:
GEAR
Planetary Gearhead GP 52 C Ø52 mm, 4 - 30 Nm, Ceramic Version Outer diameter: 52 mm Reduction: 81 : 1 Max. continuous torque: 30 Nm Part No.: 223093 (345€)
MOTOR
RE 40 Ø40 mm, Graphite Brushes, 150 Watt Part No.: 148867 (347€) Outer diameter: 40 mm Type power: 150 W Nominal voltage: 24 V No load speed: 7580 rpm Nominal torque (max. continuous torque): 177mNm
SENSOR
Encoder MR, Type L, 256 CPT, 3 Channels, with Line Driver (5V) Counts per turn: 256 Number of channels: 3 Line Driver: Yes Part No.: 225783 (93€)
Sensor has 10 pins, but cable is a 8 pole network cable, cable colors and (pin number (rj45 end))
1 NC 2 VCC - blue/white (5) 3 GND - blue (4) 4 nc 5 Ainv - orance/white (1) 6 A - orange (2) 7 Binv - green/white (3) 8 B - green (6) 9 Iinv - brown/white (7) 10 I - brown (8)
The Maxon encoder sensor is not used (march 2019)
