|
|
| (11 intermediate revisions by one user not shown) |
| Line 3: |
Line 3: |
| | === 2012 version with Xubuntu 12.04=== | | === 2012 version with Xubuntu 12.04=== |
| | | | |
| − | NB! not finished yet, but:
| + | ====Clone image to (new) disk==== |
| | + | |
| | + | Make a new bootable disk from existing image: |
| | + | |
| | + | Use '''clone-xubuntu''' and '''clone-databar''' on smr24 (room 011) as root in /root, where available images are in the ''images'' subdirectory. |
| | + | |
| | + | ====Make new boot image==== |
| | | | |
| | Update image on one of the 4GB sticks, then make new imagefile | | Update image on one of the 4GB sticks, then make new imagefile |
| Line 10: |
Line 16: |
| | * mount the disk on a local directory as root, e.g.: | | * mount the disk on a local directory as root, e.g.: |
| | sudo bash | | sudo bash |
| | + | mkdir -p disk |
| | mount /dev/sdb1 disk | | mount /dev/sdb1 disk |
| | * copy everything on disk to an image file (it takes several minutes): | | * copy everything on disk to an image file (it takes several minutes): |
| Line 17: |
Line 24: |
| | umount disk | | umount disk |
| | | | |
| − | Make a new bootable disk from the image:
| |
| − |
| |
| − | * put the destination disk on the system (if not already there), list disk devices:
| |
| − | ls /dev/sd*
| |
| − | /dev/sda /dev/sda1 /dev/sdb /dev/sdb1
| |
| − |
| |
| − | * use df to which disks are mounted (e.g. /dev/sda1 is mounted at /) :
| |
| − | df
| |
| − | Filesystem 1K-blocks Used Available Use% Mounted on
| |
| − | /dev/sda1 55805420 50781108 2228604 96% /
| |
| − | *
| |
| − |
| |
| − |
| |
| − | === New in 2011 version ===
| |
| − |
| |
| − | In order to support both VIA Nehemiah and Intel Atom based platforms two kernels must be included in the smr flash image.
| |
| − | * 2.6.32.20-rtai supports multicore systems and hyperthreading
| |
| − | * 2.6.32.20-rtai-up supports single core systems and is optimized to the Via processors
| |
| − |
| |
| − | A new clone script called <tt>multiclone</tt> must be used when this image is flashed. The script is in the root folder of rt15.
| |
| − |
| |
| − | ==== Flash cloning procedure on rt15 ====
| |
| − |
| |
| − | Via processors using CF-card flash-disks:
| |
| − | * Log in as root (If you don't know the password abort immediately)
| |
| − | * Insert the CF-card in the reader in the front of rt15.
| |
| − | * Check the device name the card is given: <tt>tail /var/log/messages</tt>. Usually it is <tt>/dev/sdb</tt>.
| |
| − | * Go to the image folder: <tt>cd image</tt>
| |
| − | * Locate the image you would like to burn (usually the newest one), for instance: <tt>flash-2011-01-01.tgz</tt>
| |
| − | * Start the procedure:
| |
| − | root@rt15:~# ../multiclone flash-2011-01-01.tgz /dev/sdb via
| |
| − |
| |
| − | ''NB: Note the two dots in front of multiclone''
| |
| − |
| |
| − | The procedure for cloning Intel Atom images is the same, except <tt>atom</tt> must be stated last in stead of <tt>via</tt> as in:
| |
| − | root@rt15:~# ../multiclone flash-2011-01-01.tgz /dev/sdb atom
| |
| − |
| |
| − | === Old description ===
| |
| − |
| |
| − | Some of the SMR's now have solid-state flash memory disks, instead of the laptop, 2.5" disks used on older models.
| |
| − |
| |
| − | This wiki page contains some notes describing how to write a bootable flash disk image (Slackware Linux) to a memory card. It assumes a Linux PC with USB flash card reader/writer, available as /dev/sda.
| |
| − |
| |
| − | The commands below is implemented in this script Clone script. Usage:
| |
| − |
| |
| − | clone <from_file.tar.gz> <to device>
| |
| − | <to device> can be both the USB bus (/dev/sdx) or a IDE device (/dev/hdx)
| |
| − |
| |
| − | The script will place a file .cloned-at on the Flash Disk with time information for the cloning.
| |
| − |
| |
| − | If you put the Flash Disk on the IDE bus and the computer will not boot (LILO - Timestamp mismatch) then the MBR on the Flash Disk must be erased as follows:
| |
| − |
| |
| − | dd if=/dev/zero of=/dev/hdx bs=1 count=512
| |
| − | Writing an image
| |
| − |
| |
| − | Format the disk, with one large Linux partition:
| |
| − |
| |
| − | sfdisk -L /dev/sda <<EOF
| |
| − | ,,L,*
| |
| − | EOF
| |
| − | Create a filesystem:
| |
| − |
| |
| − | mke2fs /dev/sda1 -L /
| |
| − | Mount the new, empty partition:
| |
| − |
| |
| − | mkdir -p /tmp/u
| |
| − | mount /dev/sda1 /tmp/u
| |
| − | Write a previously created image from flash.tar.gz
| |
| − |
| |
| − | zcat flash.tar.gz |
| |
| − | tar --extract --file - --directory /tmp/u --preserve-permissions
| |
| − | Create a patched lilo.conf, so that we can run LILO with the flash card mounted via USB. (This won't be necessary if the image written above already contains such a file.)
| |
| − |
| |
| − | patch -o /tmp/u/etc/lilo_usb.conf /tmp/u/etc/lilo.conf <<EOF
| |
| − | *** /tmp/u/etc/lilo.conf Tue Nov 4 21:34:44 2003
| |
| − | --- lilo_usb.conf Thu Dec 11 11:50:55 2003
| |
| − | ***************
| |
| − | *** 4,6 ****
| |
| − | # Start LILO global section
| |
| − | ! boot = /dev/hda
| |
| − | message = /boot/boot_message.txt
| |
| − | --- 4,7 ----
| |
| − | # Start LILO global section
| |
| − | ! boot = /dev/sda
| |
| − | ! disk = /dev/sda bios=0x80
| |
| − | message = /boot/boot_message.txt
| |
| − | EOF
| |
| − | Run LILO:
| |
| − |
| |
| − | chroot /tmp/u lilo -v -C /etc/lilo_usb.conf
| |
| − | All done:
| |
| − |
| |
| − | umount /dev/sda1
| |
| − | eject /dev/sda
| |
| − | Reading an image
| |
| − |
| |
| − | Mount as above:
| |
| − |
| |
| − | mkdir -p /tmp/u
| |
| − | mount /dev/sda1 /tmp/u
| |
| − | Read the partition:
| |
| − |
| |
| − | tar --create --file - --directory /tmp/u --one-file-system --exclude lost+found . |
| |
| − | gzip > flash.tar.gz
| |
| − | or
| |
| | | | |
| − | tar -zcf - -C /tmp/u --one-file-system --exclude lost+found . > flash.tar.gz
| + | ==Old description== |
| − | All done:
| + | |
| | | | |
| − | umount /dev/sda1
| + | [[old disk cloning procedure]] |
| − | eject /dev/sda
| + | |
