To do
From Rsewiki
(Difference between revisions)
(→Steering) |
(→Motor and turn part) |
||
| Line 26: | Line 26: | ||
====Motor and turn part==== | ====Motor and turn part==== | ||
| − | * Link between motor and wheel axle must be made in steel (not plastic) | + | |
| − | * Turn (king-pin) bolt should be 5mm, and with bigger cone for the screw. | + | (first number is priority, 1. is must, 2. is can maybe do without, 3. would be nice) |
| − | * Cut-out for motor, for raised ring on motor, should be bigger. | + | |
| + | * 1. Link between motor and wheel axle must be made in steel (not plastic) | ||
| + | * 2. Turn (king-pin) bolt should be 5mm, and with bigger cone for the screw. | ||
| + | * 3. Cut-out for motor, for raised ring on motor, should be bigger. | ||
====Big block==== | ====Big block==== | ||
Revision as of 13:52, 28 June 2017
Flexbot design to do list
Possible improvements, design ideas and other suggestions.
Back to Flexbot main page
Contents |
Mechanics
- Design of legs is too wide - move support tubes (much) closer
- turn actuator motor inwards
Foot
Assembly order:
- Fix connection (motor-to-axle-mount) to wheel axle with 2x4mm short screws, before inserting into alu wheel-stear-mount
- Alu wheel-steer-mount (with 4 bearings), insert axle assembly (from above) and secure it with wheel-nut - and fasten with pinol
- Insert 5-6mm cylinder peace into turn bearings in wheel-steer-mount, and mount into steer-mount (non turning part) with 2x5mm screws and self-locking nuts. Make sure turn motion is OK.
- Assemble motor and motor-mount block with 4x3mm screws into motor - make sure that motor in upright orientation and motor-mount matches wheel-steer-mount orientation.
- Insert motor and motor-mount assembly into axle and fixate it to wheel-steer-mount with 2x3mm 50mm long screws and self locking nuts.
- Tighten motor axle into motor-to-axle-block with 1x6mm pinol
- Insert 2x long self-cutting screws into steer-mount (a sort of reinforcement of plastic block)
- Mount foot-base (big block) to steer-mount with 4x long self cutting screws
- for steering mount blocks on motor (with strip) and on foot-base (4xsmall self cutting screws)
- Mount Firgelli actuator for steering actuation with 2x 4mm 25-35mm long screws and self locking nuts.
Motor and turn part
(first number is priority, 1. is must, 2. is can maybe do without, 3. would be nice)
- 1. Link between motor and wheel axle must be made in steel (not plastic)
- 2. Turn (king-pin) bolt should be 5mm, and with bigger cone for the screw.
- 3. Cut-out for motor, for raised ring on motor, should be bigger.
Big block
- Cut-out for teensy-print should allow more space for cable plugs.
- Space for shock absorber should be smaller.
- Width of block could be smaller.
- Pinol hole to secure PCB should be shorter - or big entry hole.
- use higher temperature for orange PETG plastic (165 degree, not 162)
Steering
- 1. Mount block on foot do not allow full actuator movement
- 2. Mount of Firgelli too sloppy, maybe a plastic adaptor in each end?
- 1. Mount block in foot end has too small screws, and may be too week.
Knee
Hip
Main body
Electronics
Power
- Main power 6-cell LiPo nominel 22.2V (between 20V and 28.5V)
Teensy
- Teensy 3.2 and Teensy 3.5 for (first level) real time control loops
Main PC
- Look at a Intel Nuc
