Inspection robot

Revision as of 13:57, 5 August 2015

Installation and use noted for 4/6-legged inspection robot.

Mobotware on a Raspberry PI

Installation - see How-to guide on main page.

Mobotware on a Beaglebone Black

Installation - ask Søren Hansen in 326/014 or Jens Christian Andersen in 326/020.

A small guide has been made, describing how to connect to the Beaglebone Black, how to mount it's file system, change I²C frequency and how to run RHD and RHDtest. The guide can be downloaded here: BBB_guide_101v3.pdf

RHD Plugin

Starting

When Mobotware has been installed, log on to the Beaglebone Black using a terminal with the following command:

ssh root@<BBB-ip>

Then navigate to the appropriate plugin folder. The exact path may vary depending on the installation. Most common paths are:

rhd/plugins/4legged/
rhd/plugins/6legged/
rhd/trunk/plugins/4legged/
rhd/trunk/plugins/6legged/

Then, the RHD can be started which will initiate I²C communication with the servo motor. To read out/set variables, RHDtest can be started in another terminal window.

NOTE: The RHD plugin needs to be compiled before using it for the first time after installation of Mobotware. This is done by navigating to the appropriate folder above, and writing the command "Make".

Features

The RHD plugin for the 4/6-legged inspection robot, as seen from the paths above, exists in two versons - one for the 6-legged robot and one for the 4-legged robot. The differences between the two plugins are minimal as both are designed for using the Beaglebone Black and communicating with the modified OpenServo PCB using I²C. Some differences exists however:

Servomotor

Hardware

The Hitec HS646-WP electric servo motor are used for the inspection robot. See Hitec's website for specifications[1]. The servo does not provide feedback by default, and is therefore augmented with the OpenServo project's PCB and software/firmware. The PCB and firmware are modified to fit the purpose of the inspection robot.

Potentiometer

Mounting: Green towards motor, yellow in center and red away from motor, or maybe more likely, motor is turned 180 deg. NOTE: The A/D converter of the ATmega168 MCU is 10-bits, giving potentiometer readouts between 0-1023.

Power

The supply voltage should be at least 6.5V to allow the regulator to properly produce 5V for the MCU. The maximum supported voltage is around 18V (the maximum rating of the weakest components). Operating with 10-12V is considered sufficient.

PCB Layout

The layout of the modified OpenServo PCB with connections can be seen in the pictures below (front and backside). A diagram/schematic of the modified OpenServo PCB can be seen here

Modified OpenServo PCB, side A

Modified OpenServo PCB, side B

Firmware

Bug

An earlier version of the firmware contains a bug that causes the firmware to crash if the PWM duty cycle becomes larger than 76% (196/255). When the firmware crashes, communication and control are lost and the servomotor will spin out of control. It is highly recommended to test if a servomotor has this bug, before use. This is tested by removing a gear from the gear-train of the servomotor and then demand a large PWM duty cycle (a P-gain of 150 and error of about 500 achieves this). If the error is present, update the servo firmware to the August 2015 version (version can be seen in main.c).

Features

As of August 2015, the servomotor firmware for the modified OpenServo PCB supports the following:

• Fixed bug that caused the firmware to crash when PWM duty cycle became larger than 76% (196/255).

• Sampling of Back-EMF (only up to duty-cycle of 76%, due to discharge time of armature coil).

• Sampling of voltage, position and armature current.

• PID control (The integration is untested).

• 500 Hz PWM control.

• Up to 400 kHz I²C bus frequency (Max supported by the ATmega168 MCU).

Needs Testing

• Integration part of build-in PID-controller.

Operational Notes

• A P-gain is needed to make the servo run. A value of about 50 is a good starting point.

• A D-gain does not affect the precision/overshooting. See the "Controller Characteristics" section for test results.

• Internal sampling of Back-EMF, voltage, position and current runs at 500 Hz (once per PWM cycle).

• Need to investigate control-part of servo.

• Maximum obtainable external sampling rate with 400 kHz I²C bus frequency was approx 1249 Hz with a single servomotor and approx 312 Hz with four servomotors (a single robot leg). However, these frequencies cannot be obtained continuously.

Controller Characteristics

Tests have been conducted with regards to determining the precision of the servomotor depending on the PD-controller gains. The table below shows the results of different step responses. Position θ, and error e (the step size), are in A/D units.

In order to avoid overshooting, small steps have been performed with large P-gains. The results can be seen in the table below. Position θ, and error e (the step size), are in A/D units.

Old RHD Plugin

The initial version of the RHD plugin was connected to a servomotor using the USBISS converter (USB-to-I²C), and is not longer used.

Setting and main status for N servos (up to 24) implemented. Debug status for 1 servo implemented (first 48 registers are monitored)

Commands (write with register adress above 0x7f) is working

0x82 (130) enable PWM
0x83 (131) disable PWM
etc - see main.c in software

Change of I²C address is not implemented in this version (There is a save to EEPROM command).