Flexbot parts list
From Rsewiki
(Difference between revisions)
(→Knee section) |
|||
| Line 2: | Line 2: | ||
=Parts list= | =Parts list= | ||
| − | This page should hold the complete parts list for Flexbot. | + | This page should hold the complete parts list for Flexbot. When adding a new component, please update correspondingly. |
==Leg== | ==Leg== | ||
| Line 9: | Line 9: | ||
* [https://www.transmotec.se/produkt/dla-12-20-a-250-hs2-ip65/ DLA-12-20-A-250-HS2-ip65] - Transmotec actuator 12V, 500N, 25cm stroke, with magnetic encoder. Each encoder channel deliveres 13.8 transitions every mm, i.e. two channels delivers a transition every 0.0362mm. At 20V (0.8A no load) motor voltage (12V motor) the hall channel period is T=6.2ms => 23mm/s, at 12V (0.65A no load) T=10.2ms => 14.9mm/s. 12V full stroke 17 sek (25cm) = 14.7mm/s. | * [https://www.transmotec.se/produkt/dla-12-20-a-250-hs2-ip65/ DLA-12-20-A-250-HS2-ip65] - Transmotec actuator 12V, 500N, 25cm stroke, with magnetic encoder. Each encoder channel deliveres 13.8 transitions every mm, i.e. two channels delivers a transition every 0.0362mm. At 20V (0.8A no load) motor voltage (12V motor) the hall channel period is T=6.2ms => 23mm/s, at 12V (0.65A no load) T=10.2ms => 14.9mm/s. 12V full stroke 17 sek (25cm) = 14.7mm/s. | ||
| + | * [http://www.robotshop.com/en/cytron-13a-5-30v-single-dc-motor-controller.html Cytron 10A DC Motor Driver] - model RB-Cyt-132 | ||
| + | * [https://www.sparkfun.com/products/13762 MPU-9250/6500] - IMU | ||
| + | * [https://www.pjrc.com/store/teensy35.html Teensy 3.5] - μ-processor board | ||
| + | * [https://www.pololu.com/product/2858 Pololu voltage regulator] - 24V to 5V | ||
| + | * Connectors and headers for the electronics - to be determined later. | ||
* - fjederben | * - fjederben | ||
Revision as of 09:49, 23 July 2017
Back to Flexbot main page
Contents |
Parts list
This page should hold the complete parts list for Flexbot. When adding a new component, please update correspondingly.
Leg
Knee section
- DLA-12-20-A-250-HS2-ip65 - Transmotec actuator 12V, 500N, 25cm stroke, with magnetic encoder. Each encoder channel deliveres 13.8 transitions every mm, i.e. two channels delivers a transition every 0.0362mm. At 20V (0.8A no load) motor voltage (12V motor) the hall channel period is T=6.2ms => 23mm/s, at 12V (0.65A no load) T=10.2ms => 14.9mm/s. 12V full stroke 17 sek (25cm) = 14.7mm/s.
- Cytron 10A DC Motor Driver - model RB-Cyt-132
- MPU-9250/6500 - IMU
- Teensy 3.5 - μ-processor board
- Pololu voltage regulator - 24V to 5V
- Connectors and headers for the electronics - to be determined later.
- - fjederben
Foot
- Firgelli L12-50-210-12-l - steering actuator (12V) 5cm stroke, with controller
- IG42CR0024x00020R - 24V drive motor with 20 pulse encoder
- TE-098-110 - SyRen 10A motor driver (24V)
- as5047 - angle encoder for damper position
Mechanics
- FIDRacing DBXL front hub (FIDXL032) steering parts, including axle (but no wheel nut)
- RovalLosi LT Wheel nut
- RovanLosi LT tyre inner foam
- -tire?
- (link) - flex coupling between motor and wheel
- (link) - 6mm axle
Body
- (link) - main PC (Intel Nuc i7?)
- (link) - batteries (LiPo?)
- (link) - USB hub (min. 8 ports)
Mechanics
Note when you know
