Terrain hopper steering
(→Maxon motor) |
(→Maxon motor) |
||
| Line 28: | Line 28: | ||
GEAR | GEAR | ||
| − | Planetary Gearhead GP 52 | + | Planetary Gearhead GP 52 |
| − | C Ø52 mm, 4 - 30 Nm, Ceramic Version | + | C Ø52 mm, 4 - 30 Nm, Ceramic Version |
| − | Outer diameter: 52 mm | + | Outer diameter: 52 mm |
| − | Reduction: 81 : 1 | + | Reduction: 81 : 1 |
| − | Max. continuous torque: 30 Nm | + | Max. continuous torque: 30 Nm |
| − | Part No.: 223093 (345€) | + | Part No.: 223093 (345€) |
MOTOR | MOTOR | ||
| − | RE 40 Ø40 mm, Graphite Brushes, 150 Watt | + | RE 40 Ø40 mm, Graphite Brushes, 150 Watt |
| − | Part No.: 148867 (347€) | + | Part No.: 148867 (347€) |
| − | Outer diameter: 40 mm | + | Outer diameter: 40 mm |
| − | Type power: 150 W | + | Type power: 150 W |
| − | Nominal voltage: 24 V | + | Nominal voltage: 24 V |
| − | No load speed: 7580 rpm | + | No load speed: 7580 rpm |
| − | Nominal torque (max. continuous torque): 177mNm | + | Nominal torque (max. continuous torque): 177mNm |
SENSOR | SENSOR | ||
| − | Encoder MR, Type L, 256 | + | Encoder MR, Type L, 256 |
| − | CPT, 3 Channels, with Line Driver (5V) | + | CPT, 3 Channels, with Line Driver (5V) |
| − | Counts per turn: 256 | + | Counts per turn: 256 |
| − | Number of channels: 3 | + | Number of channels: 3 |
| − | Line Driver: Yes | + | Line Driver: Yes |
| − | Part No.: 225783 (93€) | + | Part No.: 225783 (93€) |
Sensor has 10 pins, but cable is a 8 pole network cable, cable colors and (pin number (rj45 end)) | Sensor has 10 pins, but cable is a 8 pole network cable, cable colors and (pin number (rj45 end)) | ||
Revision as of 17:51, 7 March 2019
Back to TerrainHopper
CAD drawings
Overview of new steering proposal
Figure 1. New steering part maintaining original steering axle position, but replacing with bearings and a belt drive to a maxon gear motor. This figure points to most of the off-the-shelf parts used.
See purchase detail in Terrain-hopper binder (Christian office - red binder).
Figure 2. New steering part maintaining original steering axle position, but replacing with bearings and a belt drive to a maxon gear motor. This figure points to most of the parts that needs workshop assistance. Most of the parts - except axlesl (7 and 8) - can be manufactored on own workshop. The axles will be manufactored by axle supplier.
Maxon motor
The motor for steering is a Gear-motor-encoder combination from Maxon:
GEAR
Planetary Gearhead GP 52 C Ø52 mm, 4 - 30 Nm, Ceramic Version Outer diameter: 52 mm Reduction: 81 : 1 Max. continuous torque: 30 Nm Part No.: 223093 (345€)
MOTOR
RE 40 Ø40 mm, Graphite Brushes, 150 Watt Part No.: 148867 (347€) Outer diameter: 40 mm Type power: 150 W Nominal voltage: 24 V No load speed: 7580 rpm Nominal torque (max. continuous torque): 177mNm
SENSOR
Encoder MR, Type L, 256 CPT, 3 Channels, with Line Driver (5V) Counts per turn: 256 Number of channels: 3 Line Driver: Yes Part No.: 225783 (93€)
Sensor has 10 pins, but cable is a 8 pole network cable, cable colors and (pin number (rj45 end))
1 NC 2 VCC - blue/white (5) 3 GND - blue (4) 4 nc 5 Ainv - orance/white (1) 6 A - orange (2) 7 Binv - green/white (3) 8 B - green (6) 9 Iinv - brown/white (7) 10 I - brown (8)
The Maxon encoder sensor is not used (march 2019)
