PCB

From Rsewiki
Jump to: navigation, search

Back to Flexbot main page

Contents

Flexbot PCBs

Teensy board

Leg teensy annotated.png

Figure 1. Plug names and pin allocation for Teensy board.

  • IMU0, on-board, SCL0, pin 18-19, AD0=NC, Knee.
  • IMU1, SCL1, pin 37_38, AD0=HIGH (pin 27), Thigh (upper leg).
  • IMU2, SCL1, pin 37_38, AD0=NC, Shin (lower leg).
  • IMU3, SCL2, pin 3_4, AD0 = HIGH (pin 28), Foot.
  • IMU4, SCL2, pin 3_4, AD0 = NC, Hip.

Actuators

Steering

  • 1: 12V,
  • 2: PWM pin 5 - moved to pin 29 (timer FTM2 200 Hz?), Patch on rev A2, clean in rev B
  • 3:pot pin 23 (A9),
  • 4: GND

Actuator 1 - upper leg

motor

  • 1: (5V) nc.
  • 2: PWM pin 21 (timer FMT3)
  • 3: direction pin 26
  • 4: GND

encoder

  • 1: 5V
  • 2: A pin 39
  • 3: B pin 30 - patched from A21 DAC0 on rev A2, clean on rev B
  • 4: GND

current sensor

  • 1: 5V
  • 2: sense pin 16 (A2)
  • 3: gnd

Actuator 2 - lower leg

Motor

  • 1: direction pin 25
  • 2: PWM pin 22 (timer FMT0)
  • 3: GND

encoder

  • 1: 5V
  • 2: A pin 5 - patched from A22/DAC1 on rev A2, clean on rev B
  • 3: B pin 36
  • 4: GND

current sensor

  • 1: 5V
  • 2: sense pin 15 (A1)
  • 3: gnd

Wheel

motor driver

  • 1: nc (not connected on rev B, must not be connected on rev A2 (+5V source both ends))
  • 2: PWM pin 2 (timer FTM3) (S1) (RC mode 200 Hz?)
  • 3: GND - NB! connected to motor power GND (probably OK to connect)

encoder

  • 1: 5V
  • 2: A pin 35
  • 3: B pin 34
  • 4: GND

current

  • 1: 5V
  • 2: sense pin 17 (A3)
  • 3: GND

Cables in leg

Cables-in-leg.png

Figure 2. Overview of cables in one leg with some wire details. The connection to robot base platform is 24V (10A) and USB only. Steering servo should be in RC servo interface mode.

Wheel motor driver in RC mode: switch 1=off, all others ON. S1 used only.

Controller block diagram

Leg teensy-block-function.png

Figure 3. Functional blockdiagram og Teensy controller board. Not all blocks and MAV messages are implemented yet.

Teensy board and schematic

Leg teensy board.png

Figure 4. Layout of PCB revision A2 (designed in Eagle).


Leg teensy schematic.png

Figure 5. PCB schematic revision A2 - click on image to get better view.

Teensy board patches annotated.png

Figure 6. Needed patches from version A2 to revision B. PWM for steering servo in RC mode now moved to timer FMT3 on pin 29 (old connection to pin 5 must be cut). Actuator 2 encoder A also connected to pin 5 (for interrupt), and actuator 1 encoder B also connected to (free) pin 30 - also for interrupt (annotated image has error Act 1<->2). The last 2 maintains connection to DAC pins and pull-up resistors.



--Jca (talk) 13:03, 9 June 2018 (CEST)

Personal tools
Namespaces

Variants
Actions
Navigation
Toolbox