Flexbot parts list
From Rsewiki
(Difference between revisions)
(→PCB and cables) |
(→Leg) |
||
| (One intermediate revision by one user not shown) | |||
| Line 13: | Line 13: | ||
[[File:leg_teensy_board.png | 600px]] | [[File:leg_teensy_board.png | 600px]] | ||
| − | = | + | =Legs= |
==Hip section== | ==Hip section== | ||
| Line 24: | Line 24: | ||
* [https://www.transmotec.se/produkt/dla-12-20-a-250-hs2-ip65/ DLA-12-20-A-250-HS2-ip65] - Transmotec actuator 12V, 500N, 25cm stroke, with magnetic encoder. Each encoder channel deliveres 13.8 transitions every mm, i.e. two channels delivers a transition every 0.0362mm. At 20V (0.8A no load) motor voltage (12V motor) the hall channel period is T=6.2ms => 23mm/s, at 12V (0.65A no load) T=10.2ms => 14.9mm/s. 12V full stroke 17 sek (25cm) = 14.7mm/s. | * [https://www.transmotec.se/produkt/dla-12-20-a-250-hs2-ip65/ DLA-12-20-A-250-HS2-ip65] - Transmotec actuator 12V, 500N, 25cm stroke, with magnetic encoder. Each encoder channel deliveres 13.8 transitions every mm, i.e. two channels delivers a transition every 0.0362mm. At 20V (0.8A no load) motor voltage (12V motor) the hall channel period is T=6.2ms => 23mm/s, at 12V (0.65A no load) T=10.2ms => 14.9mm/s. 12V full stroke 17 sek (25cm) = 14.7mm/s. | ||
* [http://www.robotshop.com/en/cytron-13a-5-30v-single-dc-motor-controller.html Cytron 10A DC Motor Driver] - model RB-Cyt-132 | * [http://www.robotshop.com/en/cytron-13a-5-30v-single-dc-motor-controller.html Cytron 10A DC Motor Driver] - model RB-Cyt-132 | ||
| − | * [https://www.sparkfun.com/products/13762 MPU-9250/6500] - IMU (x3) --- nej, ikke Sparkfun, men det "blå" breakout print. | + | * [https://www.sparkfun.com/products/13762 MPU-9250/6500] - IMU (x3) --- nej, ikke Sparkfun, men det "blå" breakout print - dog lille sparkfun til version B print. |
* [https://www.pjrc.com/store/teensy35.html Teensy 3.5] - μ-processor board | * [https://www.pjrc.com/store/teensy35.html Teensy 3.5] - μ-processor board | ||
* [https://www.pololu.com/product/2858 Pololu D24V22F5] - 24V to 5V voltage regulator | * [https://www.pololu.com/product/2858 Pololu D24V22F5] - 24V to 5V voltage regulator | ||
Latest revision as of 11:11, 6 November 2018
Back to Flexbot main page
Contents |
[edit] Introduction
This page should hold the complete parts list for Flexbot. When adding a new component, please update correspondingly.
[edit] PCB and cables
The printed circuit boards and cabling are described here:
All PCB and connector pinout
[edit] Legs
[edit] Hip section
- MPU-9250/6500
- DLA-12-10-A-150-HS2-ip65 - Transmotec actuator 12V, 300N, 15cm stroke, with magnetic encoder.
[edit] Knee section
- DLA-12-20-A-250-HS2-ip65 - Transmotec actuator 12V, 500N, 25cm stroke, with magnetic encoder. Each encoder channel deliveres 13.8 transitions every mm, i.e. two channels delivers a transition every 0.0362mm. At 20V (0.8A no load) motor voltage (12V motor) the hall channel period is T=6.2ms => 23mm/s, at 12V (0.65A no load) T=10.2ms => 14.9mm/s. 12V full stroke 17 sek (25cm) = 14.7mm/s.
- Cytron 10A DC Motor Driver - model RB-Cyt-132
- MPU-9250/6500 - IMU (x3) --- nej, ikke Sparkfun, men det "blå" breakout print - dog lille sparkfun til version B print.
- Teensy 3.5 - μ-processor board
- Pololu D24V22F5 - 24V to 5V voltage regulator
- Connectors and headers for the electronics - to be determined later.
- - fjederben
[edit] Foot
- Firgelli L12-50-210-12-l - steering actuator (12V) 5cm stroke, with controller
- IG42CR0024x00020R - 24V drive motor with 20 pulse encoder, gear 1:24.
- TE-098-110 - SyRen 10A motor driver (24V)
- as5047 - angle encoder for damper position
- Pololu D24V22F5 - 24V to 5V voltage regulator
- Pololu D24V22F12 - 24V to 12V voltage regulator
- Connectors and headers for the electronics - to be determined later.
[edit] Mechanics
- FIDRacing DBXL front hub (FIDXL032) steering parts, including axle (but no wheel nut)
- RovalLosi LT Wheel nut
- RovanLosi LT tyre inner foam
- -tire?
- (link) - flex coupling between motor and wheel
- (link) - 6mm axle
[edit] Body
- (link) - main PC (Intel Nuc i5?)
- 24V -> 19V NUC power 100w (https://www.cartft.com/catalog/il/2026)
- batteries (LiPo - 5Ah, 2 x 3 cells 22.2V nominel (110Wh), (20-29V aktuelt)
- charger 2x e430 SKYrc 2-4 cell (https://www.motionrc.eu/pages/search-results-page?q=e430+30w)
- USB3 hub 7 port 24V (https://www.cartft.com/catalog/il/1978)
[edit] Mechanics
Description - of some of the 3D printed parts
Parts for steering actuator mounting.
Parts for foot rear set, left and right.
