Robobot circuits
(→PCB) |
|||
| (7 intermediate revisions by one user not shown) | |||
| Line 2: | Line 2: | ||
== Digital IO == | == Digital IO == | ||
| + | |||
| + | === Circuit diagram === | ||
[[File:digital_IO-circuit.png | 900px]] | [[File:digital_IO-circuit.png | 900px]] | ||
| Line 9: | Line 11: | ||
If output, then a transistor is active when output is high, and can draw at least 1A from the 12V supply. | If output, then a transistor is active when output is high, and can draw at least 1A from the 12V supply. | ||
The 5V and 3.3V can supply no more than 100mA. | The 5V and 3.3V can supply no more than 100mA. | ||
| + | |||
| + | === PCB === | ||
[[File:digital_IO-PCB.png | 900px]] | [[File:digital_IO-PCB.png | 900px]] | ||
| Line 16: | Line 20: | ||
== Regbot == | == Regbot == | ||
| + | |||
| + | === Circuit diagram === | ||
[[File:regbot_6.3.png | 900px]] | [[File:regbot_6.3.png | 900px]] | ||
Figure 3. The Regbot circuit. | Figure 3. The Regbot circuit. | ||
| + | |||
| + | === PCB - 3D view === | ||
[[File:regbot_6.3_PCB.png | 900px]] | [[File:regbot_6.3_PCB.png | 900px]] | ||
| + | |||
| + | === PCB === | ||
Figure 4. Ecpected view of PCB. | Figure 4. Ecpected view of PCB. | ||
| Line 28: | Line 38: | ||
Figure 5. PCB with more trace details. | Figure 5. PCB with more trace details. | ||
| + | |||
| + | == Line sensor == | ||
| + | |||
| + | === Circuit === | ||
| + | |||
| + | [[File:line_sensor_3.1_circuit.png | 700px]] | ||
| + | |||
| + | Figure 6. Circuit diagram for the line sensor. 8 sensors with a change amplifier and analog output. The 18 LEDs provides the blinking light (1kHz). | ||
| + | |||
| + | === PCB === | ||
| + | |||
| + | [[File:line_sensor_3.1_PCB_3D.png | 700px]] | ||
| + | |||
| + | Figure 7. The PCB in 3D view. The distance from the first to the last sensor is 12cm. | ||
| + | |||
| + | [[File:line_sensor_3.1_PCB.png | 700px]] | ||
| + | |||
| + | Figure 8. PCB layout. | ||
| + | |||
| + | == Raspberry PI == | ||
| + | |||
| + | [[File:Raspberry_Pi_GPIO_pins.png | 500px]] | ||
| + | |||
| + | Figure 9. GPIO pin numbers. | ||
Latest revision as of 11:02, 28 December 2023
Back to Robobot_B
Contents |
[edit] Digital IO
[edit] Circuit diagram
Figure 1. The circuit diagram should ensure that each IO pin can function as both input and output. If input, then the pin has active pull down, i.e. for input to change, it must be pulled high, to at least 3.3V, but 5 or 12V will work too. If output, then a transistor is active when output is high, and can draw at least 1A from the 12V supply. The 5V and 3.3V can supply no more than 100mA.
[edit] PCB
Figure 2. The PCB layout for the digital IO circuit.
[edit] Regbot
[edit] Circuit diagram
Figure 3. The Regbot circuit.
[edit] PCB - 3D view
[edit] PCB
Figure 4. Ecpected view of PCB.
Figure 5. PCB with more trace details.
[edit] Line sensor
[edit] Circuit
Figure 6. Circuit diagram for the line sensor. 8 sensors with a change amplifier and analog output. The 18 LEDs provides the blinking light (1kHz).
[edit] PCB
Figure 7. The PCB in 3D view. The distance from the first to the last sensor is 12cm.
Figure 8. PCB layout.
[edit] Raspberry PI
Figure 9. GPIO pin numbers.
