Regbot

Small robot intended for control-1 exercises.

Hardware

Design overview can be found here.

REGBOT comes in 2 versions:

• version 1A - with robot numbers 1..15
• version 2B - with robot numbers 16..

REGBOT robot status

Use software as is

To use regbot two software parts are needed - one for the robot (regbot.hex) and the client (regbot.exe (for windows)).

Client software

Get the client software (regbot.exe) from file sharing on campusnet, place it in a directory, this directory will be default for configuration file and result files from the robot.

A USB driver must be installed to get in contact with the robot - see installation in windows

The driver will (on Windows) create a com-port when connected - most likely com3 or any higher number. When the robot is disconnected by unplugging the cable, then the client probably needs to be restarted if it was connected when the cable was unplugged (no connection detect in windows).

The run the regbot.exe file.

User interface

The user interface can configure and run the robot, as well as inspecting almost all values on the robot. Written in python using Qt GUI library.

The User interface page has details.

Robot software

The robot software is compiled into a regbot.hex file, that is loaded into the robot flash disk using a teensy loader.

The loader is found here https://www.pjrc.com/teensy/loader.html.

Start the teensy loader - it looks like this

Load the regbot.hex file (found on file sharing for the course) into the teensy loader application.

With the robot connected over USB, press the small "software load" button on the teensy board.

NB! It may take up to 30 seconds before the teensy loader detects the board.

Then press "Program" and "Reboot" on the teensy loader application. It may be necessary to press the big "reboot" or "power" button on the robot itself also. On some robots a total power cycle is needed to reboot properly. The robot should blink every 1 second with a short blink.

Software download

The source code for the robot and the client is available here. NB! the software source can not be compiled without the proper tool-chain (compiler and library for the robot and python and libraries for the client)

• Robot software (including regbot.hex): version 2.301 (as of 10 February 2016) - fixed error in disabling faulty velocity estimator.
• Robot software (including regbot.hex): version 2.290 (as of 5 February 2016) - fixed loss of ID if saved mission has more than a few lines.
• Robot software (including regbot.hex): version 2.285 (as of 31 January 2016) - ready for F16 course

• Client software : 2.290 (as of 5 February 2016) - fixed tilt offset error en saved configuration file (regbot.ini)
• Client software (including regbot.exe for windows): 2.285 (as of 31 January 2016) - ready for F16 course

repository for software - client and robot

• client: svn://repos.gbar.dtu.dk/jcan/regbot/qtgui
• robot: svn://repos.gbar.dtu.dk/jcan/regbot/regbot
• robot version 2.290 as zipfile from dropbox https://www.dropbox.com/s/s71s4w1x61cwpb2/regbot_290.zip?dl=0 )

On a Linux computer do something like this:

svn co svn://repos.gbar.dtu.dk/jcan/regbot/regbot .
svn co svn://repos.gbar.dtu.dk/jcan/regbot/qtgui .

Install software tools

The software tools to modify the software requires some tools.

• Software installation and tool-chain - Linux
• installation in windows and some of the tool-chain
• Schematic

Vision based Line Follower

When turning on the RegBot the Raspberry Pi and the Line Follower application will automatically start.

To wirelessly control and communicate with the RegBot and the Line Follower application open up a SSH session by using Putty on Windows and Terminal on Linux and Mac.

To access the RegBot type in:

ssh pi@hostname.local

where hostname should have been changed to regbotxx corresponding to the robots number.

The default password to a Raspberry Pi is raspberry, but this should have been changed to e.g. filippa corresponding to the robots name.

When the SSH session is open attach to the running Line Follower instance:

tmux attach

This will present a window like this:

In the bottom window 1 should be presented as 1:linefollow.

To attach to window 1 press Ctrl+B then 1.

As usual typing help will list the available commands for the RegBot.

Typing pihelp will give a list of commands to the Line Follower application:

         ### COMMANDS ### 

pihelp:               this text
left:                 regbot will make left turns [default]
right:                regbot will make right turns
linemode=0:           regbot will run till end of line [default]
linemode=xxxx:        regbot will run till xxxx frames have been captured
black:                regbot will run on black lines [default]
white:                regbot will run on white lines

        ### ######## ###

To run the Line Follower mission on the RegBot change the mission to M=8.

To detach (exit) the session do not type exit as this will shut down the running instance. Instead press Ctrl+B then D to detach.

Go to Vision based Line Follower for detailed information on the project and instructions on how to setup a new Line Following RegBot.